Parts Call for your nearest distributor, product info or www.specprod.com 1-800-525-6505 Technical Assistance • In the USA and Canada 106 CHRYSLER MINI-VAN SHIMS For camber and toe change, use our mini-van shims that allow for quick and easy changes in increments of: toe .10° and camber .25°. 71700SHIMSET - Includes 20 shims/2 of each size Rear Adjustment range: Camber ±1.00°/Toe ±.10° to ±.80° Required: 1 shim per wheel/ per angle changed APPLICATIONS Chrysler 1996 - 16 Town & Country FWD: 2000 - 03 Voyager Dodge 1996 - 07 Caravan FWD: 1996 - 20 Grand Caravan Ram 2012 - 15 Tradesman FWD: Conversion Van Nissan: 2007 -12 Sentra Plymouth FWD: 1996 - 01 Voyager Volkswagen FWD: 2009 - 14 Routan F m a t 7 71700 SERIES CAMBER Degree TOE Degree Degree Part No. of Change Part No. of Change Part No. of Change 71730 ±.25° (1/4°) 71720 ±.10° [.05” (1/16”)] 71723 ±.40° [.20” (3/16”)] 71731 ±.50° (1/2°) 71721 ±.20° [.10” (1/8”)] 71724 ±.50° [.25” (1/4”)] 71732 ±.75° (3/4°) 71722 ±.30° [.15” (5/32”)] 71725 ±.80° [.40” (3/8”)] 71733 ±1.00° (1°) NISSAN HUB SHIM HARDWARE Rear Adjustment range: Camber ±.25°, ±.50°, ±1.00° Toe ±.10 to ±.50° Required: 1 or 2 shims per wheel APPLICATIONS Nissan: 2011 - 17 Juke 2011 - 24 Leaf Use these longer bolts on the rear axle Nissan Leaf and Juke when djusting the alignment with the 71700 series shims. The factory bolts often aren’t long nough when camber and toe e adjusted using SPC’s axle ms, these longer bolts ensure engagement on the rear per kit, only one kit is needed Use these lo for theN ad t f e are shim proper thread hubs. Sold 8 p per vehicle. 71715 TOE Part No. Change 71621 ±.10° 71622 ±.20° 71623 ±.30° 71624 ±.40° 71625 ±.50° CAMBER 71631 ±.25° 71632 ±.50° TOYOTA SIENNA REAR CAMBER AND TOE SHIMS Rear Adjustment range: Camber ±.25° and ±.50° Toe ±.10° to ±.50° Required: 1 or 2 shims per wheel APPLICATIONS Toyota AWD/FWD: 2011- 20 Sienna 71600 SHIMSET - Includes 14 shims/2 of each size. These full contact shims correct camber and/or toe on both AWD and FWD Toyota Siennas. Combination adjustments, or changes up to 1° may be made by stacking up to 2 shims per side. 71600 SERIES VW/AUDI REAR SHIMS With these shims you can correct rear camber and toe on newer Volkswagens and Audis. By combining the shims (two may be used on each wheel) you can get ±.50° to ±1.0° camber change and up to ±.50° toe change. Our wrench (#87530) is a must when installing these shims. It allows you to remove the brake sensor ring, bearing, seal and hub assembly as one unit. 71500 SHIMSET Includes 16 shims/2 of each size and 87530 wrench. Rear Adjustment range: Camber ±.50° to ±1.00°/ Toe ±.13° to ±.50° Required: 1 shim per wheel/per angle changed APPLICATIONS Audi FWD: 2000 - 06 TT Volkswagen: 1998 - 10 Beetle 1999 - 06 Golf (Except R32) 1999 - 06 GTI 1999 - 05 Jetta (Beam Rear Axle) CAUTION: Check brake & rotor clearance for binding. 75970 spacers TOE Part No. Change 71520 ±.13° 71521 ±.25° 71522 ±.38° 71523 ±.50° CAMBER 71530 +.50° 71531 +1.00° 71532 -.50° 71533 -1.00° NOTE: When installing these shims we recommended that you use our VW Shim Wrench (#87530 pg. 170) to assist in removing the rear hub. g p (page 118) maybe required. 87530 - Wrench 71500 SERIES
RkJQdWJsaXNoZXIy OTk3MQ==